- PHONE
- (62) 22 87801723
- info@grahamandala.com
ACS Safety Datasheet
- Home
- ACS Safety Datasheet
Product & Safety Datasheets
Australia Safety Data Sheet (SDS) for
ACS CIC Thermal Insulation Coatin
| Product Name | Industrial & Marine Ceramic Insulation Coating |
| Product Code | ACS CIC Insulation Coatings-Industrial |
| Common Chemical Name | Acrylic & Insulation Particle-based Coating |
| Manufactured By | Advanced Coating Solutions LLC |
| Emergency Telephone | 888-779-4223 |
| Address | 218 Main Street, 429 Kirkland, WA 98033 |
| Australian Point of Contact | Deltacoat Pty Ltd
18/6 Quarimor Road, Bibra Lake WA 6163, Australia +618 9494 2300 |
| Australian Emergency
Telephone |
Office Hours : + 618 9418 7200
After Hours : 0418 920 789 |
| Product Use | Insulation coating for personnel protection and energy retention. |
| Not Recommended For | Unintentional Uses |
| Other Information | While descriptions, designs, data and other information contained herein are presented in good faith and believed to be accurate, it is provided for guidance only. Because many factors may influence the processing or application/use, ACS recommends that tests be made for the suitability of the product in the intended purpose. The intended use of this document is for health and handling procedures and not intended for an ingredients list for reformulation. Ingredients are given as a range with the actual formulation considered a trade secret. This sheet may contain information that is not used in this formulation in all purposes but rather as a guideline as to what can be used in this formulation. Actual percentages and specific ingredients are considered a trade secret. Ingredients listed on the MSDS as proprietary or trade secrets are considered confidential to ACS by raw material supplier. |
This product is considered to be non-hazardous.
| GHS Ratings | There are no GHS ratings that apply to this product at this time |
| GHS Hazards | None Known |
| GHS Precautions | None Known |
| Chemical Name | CAS No | Amounts (%) | Osha Exposure
Limits |
ACGIH Exposure
Limits |
| Modified Acrylic
Resin |
Proprietary | 46.4 | N/A | N/A |
| Water | 7732-18-5 | 22.3 | N/A | N/A |
| Insulation Particles | N/A | 21 | 15mg/m3 | 15mg/m3 |
| Wetting Agent | 474000-95-8 | 0.4 | 15mg/m3 | 5mg/m3 |
| Titanium Dioxide | 1346-67-7 | 5.1 | 10mg/m3 | 10mg/m3 |
| Inert Pigment | N/A | 5.8 | 15mg/m3 | 15mg/m3 |
| Additives | N/A | 2.6 | N/A | N/A |
Note *** All Dry Ingredients are encapsulated with resin which will minimise exposure
| Inhalation | Move to fresh air. Aide in breathing if needed and get immediate
medical attention. |
| Eye Contact | Flush eyes with water immediately. Get immediate medical attention. |
| Skin Contact | Wash area with soap and water. If redness persists, seek medical
attention. |
| Ingestion | If swallowed, dilute with water. DO NOT INDUCE VOMITING. Never give fluids or induce vomiting if the victim is unconscious or having
convulsions. Get immediate medical attention. |
| Notes to Physicians | None Known |
| Special Instructions | None Known |
| Extinguishing Media | Use Carbon Dioxide (CO2). “Alcohol” foam, Dry Chemical or water
spray/water fog extinguishing systems. |
| Unusual Fire of Explosion Hazards | Product will not burn but may spatter if temperature exceeds boiling point. Extreme heat may cause closed containers to burst. Dried film of
product is capable of burning, giving off oxides of carbon/nitrogen. |
| Hazardous Combustion
Products |
See section 10 for a list of hazardous decomposition products for this mixture. |
| Fire Fighting | If evacuation of personnel is necessary, evacuate to an upwind area. Use water fog/water spray to col closed adjacent containers to prevent pressure build up. Decontaminate personnel and equipment with a water
wash-down after fire and smoke exposure. |
| Fire Fighting
Equipment |
Fire Fighters and emergency personnel should wear full protective gear
including self-contained breathing apparatus (SCBA). |
| Unusual Fire and Explosion | Product will not burn but may spatter if temperature exceeds boiling point. Extreme heat may cause closed containers to burst. Dried film of
product is capable of burning, giving off oxides of carbon/nitrogen. |
| Spills and Leak Procedure | Spill supervisor – Ensure cleanup personnel wear all appropriate personnel- protective equipment (PPE). Keep non-essential personnel away from the
contaminated area. |
| Small Spills | Mix appropriate absorbent into the spilled material. Sawdust or kitty litter may be used. Collect the saturated absorbent and transfer it into a covered
container(s). |
| Large Spills | Prevent materials from entering sewers and watercourses by diking or impounding the spilled material. Advise authorities if the product has entered or may enter sewers, watercourses or extensive land areas. Mix appropriate absorbent into the spilled material. Sawdust or kitty litter may be used. Collect
the saturated absorbent and transfer it into a covered container(s). |
| Waste Disposal | Waste from this material is not hazardous as defined by the Resource Conservation and Recovery Act (RCRA) 40 CFR 261. Incinerate in approved facility. Do not incinerate closed containers. Dispose of in accordance with
Federal, State, and Local regulations. |
| Handling Precautions | Wear all appropriate Personnel Protective Equipment (PPE). Ensure adequate ventilation during use and storage. Keep
containers closed when not in use. Store in original containers. |
| Storage Requirements | Protect from freezing and keep out of direct sunlight for extended periods. A climate-controlled warehouse is best for
product. |
| Regulatory Requirements | None Known. |
| Occupational Exposure Limit
Values |
No exposure value assigned for this material by SafeWork Australia. | |||
| Chemical Name | CAS No | Amounts (%) | Osha Exposure
Limits |
ACGIH Exposure
Limits |
| Modified Acrylic
Resin |
Proprietary | 46.4 | N/A | N/A |
| Water | 7732-18-5 | 22.3 | N/A | N/A |
| Insulation Particles | N/A | 21 | 15mg/m3 | 15mg/m3 |
| Wetting Agent | 474000-95-8 | 0.4 | 15mg/m3 | 5mg/m3 |
| Titanium Dioxide | 1346-67-7 | 5.1 | 10mg/m3 | 10mg/m3 |
| Inert Pigment | N/A | 5.8 | 15mg/m3 | 15mg/m3 |
| Additives | N/A | 2.6 | N/A | N/A |
| Engineering Controls | Airless spray for application is preferred to minimise overspray. Provide ventilation sufficient to remove airborne particles. Use good painting
practices. |
| Ventilation | Use only with adequate ventilation. Ventilation should be sufficient to keep
the area within occupational exposure limits. |
| Administrative
Controls |
None known |
| Protective Equipment | A dust respirator is recommended even with adequate ventilation. Do not use respirators beyond their capacities. In the event that occupational exposure limits may be exceeded, use an approved air supplied respirator or
positive pressure, self-contained breathing apparatus (SCBA) |
| Contaminated Equipment | Contaminated equipment should be washed before reuse or discarded. Dried paint on clothing is no-hazardous. Equipment should be thoroughly cleaned after use. Dispose of any waste in accordance with all Federal, state, regional
and local regulations. |
| Appearance | Smooth Creamy White
Liquid |
Odour | Slight ammonia odour |
| Vapour
Pressure |
No data | Odour
threshold |
No data |
| Vapour Density | Same as water vapour | pH | 9.2-9.6 |
| Specific Gravity | 0.63 | Melting Point | No data |
| Freezing Point | 0OC (32OF) | Solubility | Can be diluted with water |
| Boiling Range | Approx. 100oC (212°F) | Flash Point | None |
| Evapouration
Rate |
= Water | Flammability | Liquid coating will not burn |
| Explosive Limits | None | Partition
coefficient |
No data |
| Auto-ignition
Temp. |
>316OC (>600oF) | Decomposition
Temp |
232 OC (450 OF) (dry coating) |
| Viscosity | 20,000-50,000cP | Lbs. VOC/Gal | 0.06 lbs./gallon (7.6g/Litre) |
| Stability Data: | Stable |
| Incompatibility: | Solvents with coagulate the product |
| Conditions or Hazards to Avoid: | Extreme temperatures above 500°F (260°C) |
| Hazardous Decomposition: | Hazardous polymerization will not occur. |
| Corrosive Properties: | Not corrosive |
| Oxidizer Properties: | Not an oxidizer |
| Chloride Properties: | None |
| Mixture Toxicity | None known |
| Component Toxicity | None known |
| Toxicological Information | No data |
| Routes of Entry | Ingestion, inhalation of overspray if proper ventilation or PPE not
adopted. |
| Target Organs | None known |
| Effects of Overexposure | None known |
| Carcinogen Rating | None present in any reportable quantity |
No applicable data in this section.
Avoid ordering too much material. The best disposal practice is to use up left over material. Material may be solidified with cement and disposed of according to local, state, regional and Federal regulation. Dry material is non-hazardous.
Non-hazardous water based paint. Not regulated by 49 CFR, IATA or IMO. DOT Proper shipping name: None
| Agency | Proper Shipping
Name |
UN No | Packing Group | Hazard Class |
| DOT | Not applicable | Not applicable | Not applicable | Not applicable |
| IATA | Not applicable | Not applicable | Not applicable | Not applicable |
| IMDG | Not applicable | Not applicable | Not applicable | Not applicable |
Bill of Lading Description: Class 55
Air Freight: Acceptable, Non-Combustible
| TSCA Inventory Status | Listed in Inventory- Yes |
| RCRA Hazard Waste No | Not applicable |
| CERCLA | No |
| Stat Regulatory Info | See Ingredients (Section 3) |
Hazardous ratings: TTS currently uses the National Paint and Coatings Association rating system. The use of an asterisk (*) in the HMIS rating indicates the potential for chronic health effects
| HMIS: | ||
| Health Fire | Physical Hazard | |
| 1 | 0 | 0 |
Hazardous rating OSHA: The product is considered NON- HAZARDOUS by the OSHA Hazard Communication Standard.
Shipping: This product is considered non-hazardous and acceptable to transport via ground freight, ocean freight, or air freight without special handling. It is considered a Class 55 shipment product in the United States.